![]() If you answered Enable Telemetry when you first started, PeakHour will downloading 'friendly' interface names for common routers such as Apple's Airport range to help make things a little easier.One of our firewalls is an SG-3100 running 2.4.4-RELEASE-p1 It's not really possible to list them because it differs from manufacturer to manufacturer and device to device. ![]() To monitor Internet traffic, commonly the interface will be called something like wan0, pppoe0, internet or something similar. On most devices, each of these is a separate interface and you will need to tell PeakHour which one to use. In addition, it might also have a WiFi interface for wireless devices to connect to. For example, your broadband router might have a WAN / Internet Port as well as a number of LAN (local) ports that you plug other devices into. Most devices have more than one 'interface'. Once you've configured your device, click Next to see the list of interfaces. You can adjust other settings such as the SNMP security settings and version, as required by your device. If this doesn't work or the device name / ip address is wrong, uncheck automatically discover and enter the name or ip address of the device you wish to monitor. Your default router supports SNMP and it is enabled.Your default router can be detected (almost always).By default, Automatically detect is checked so PeakHour will try to find your default gateway or router automatically. When you choose SNMP, you're first taken to the Locate your device page. SNMP doesn't support automatic detection so you will need know the IP address of the device. If you're unsure about which device to monitor, the real-time throughput information can help. To the right of that is a real-time output of the device's currently detected throughput. Along with the name of the device, information such as the device's Internet IP address, connection type and link status are displayed. This screen (shown above) displays a summery of the UPnP devices that PeakHour is capable of monitoring. Choosing a deviceĬhoosing UPnP will take you to the list of detected devices. If it shows no UPnP devices available or UPnP is disabled (greyed out), you will most likely need to try SNMP. If you see that device(s) have been detected, this is a good sign that your Internet router supports UPnP. You'll notice that the number of automatically detected UPnP devices is displayed (in the above screenshot "2 available devices"). You should try this first if you're unsure about what protocol(s) your device supports. UPnP is the simplest option as it is completely automatic and requires no configuration. Note for SNMP, you will need to know the IP address of the device, as it does not support automatic detection. Try both UPnP and SNMP options to see which one works.Most routers have the the option to enable these features within their admin interface, and those options are documented in the manual. ![]() Search the manual for an occurrences of "UPnP" and "SNMP". Download the instruction manual / admin guide from the manufacturers web site.As a general rule of thumb, most Internet routers support UPnP at least, so try this first. This is entirely depending on what sort of device it is. The first question you're asked is: which protocol to use? Describe the target and choose any final options.(SNMP only) Choose which interface to monitor.Locate your device, either automatically (UPnP) or by entering it's hostname / IP address (SNMP).Some routers support both, most support UPnP only. Your choice is mostly determined by your router and what it supports. Determine which protocol to use: SNMP or UPnP.These are the steps you'll go through to configure your first target: You can configure as many targets as you wish. A target is a network device or interface that is monitored by PeakHour. When you first launch PeakHour or PeakHour Compatibility Check, the Configuration Assistant will open and walk you through configuring your first device (or 'target'). This guide is to help step you through getting started with the PeakHour Compatibility Check or getting the PeakHour app up and running.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |